转让电话:13313028229

  • 首页
  • 产品展示
  • 行业方案
  • 新闻中心
  • 关于我们
  • 联系我们
新闻动态
  • 新闻动态
新闻动态 当前位置:首页>新闻动态>新闻动态

打标针有时冲击有时不冲击

网址:www.dabiaoji58.com.cn  2022-09-20  作者:admin    阅读:

打标针有时冲击有时不冲击,刻印的字符残缺不全
Marking needles sometimes impact, sometimes do not impact, printed characters incomplete
(1)气路中和电磁阀内有较多的水,或电磁阀内有杂物。清除气路中的积水,空压机也要定时放水(一个月至少一次)。清除电磁阀内的杂物并加些润滑脂。
(1) The air circuit neutralizes more water in the solenoid valve or impurities in the solenoid valve. Clean up the accumulated water in the air passage, the air compressor should also release water regularly (at least once a month). Clean up the sundries in the solenoid valve and add some grease.
(2)打标针套内(打标针套内和打标针之间)有脏物,用煤油清洗打标针套和打标针,然后往针套内或打标针上加少量(随机配带的)专用的润滑油或白色的润滑脂。
(2) There are dirt in the marking needle sleeve (between the marking needle sleeve and the marking needle). Clean the marking needle sleeve and the marking needle with kerosene, and then add a small amount of special lubricating oil or white grease to the needle sleeve or marking needle.
(3)打标针上端的铜与打标头内的"O"型橡胶密封圈接触不好,调整弹簧的长度更换"O"型圈,重装"O"型圈。
(3) The copper on the top of the marking needle does not contact the O-type rubber sealing ring in the marking head well. The length of the spring is adjusted to replace the O-type ring and the O-type ring is reassembled.
(4)气路堵塞或气管弯折造成气体流量不够,打标刚开始时打得深,后来轻或后来打标针不冲击。应检查气路排除堵塞或弯折。
(4) Gas flow is insufficient due to blockage of air passage or bending of trachea. The marking is deep at the beginning, then light or later, the marking needle is not impacted. The airway should be checked to remove blockage or bending.
(5)字符的坐标位置设置不合理,太靠边造成一部份笔划未刻印出来,请调整周边字符的坐标位置。
(5) The coordinate position of characters is unreasonable, too close to the edge causes some strokes not to be printed out. Please adjust the coordinate position of peripheral characters.
(6)电脑的原因。
(6) The reason of computer.
A、关掉电脑重新启动;
A. Turn off the computer and restart it.
B、关闭其它程序如音乐播放器等;
B. Turn off other programs such as music player, etc.
C、打标机工作时不要在屏幕保护状态下。
C. Don't use screen saver when marking machine works.
要想气动打标机在日常工作中能很好的工作,那就必须做到一下几点:
If you want pneumatic marking machine to work well in daily work, you must do a few things:
1.打标针及针套的保养:
1. Maintenance of marking needles and needle covers:
保养时将打印针从针套中取出,用汽油将它们清洗干净,擦干后加入适量润滑油,重新装入即可。该项工作根据用户使用设备的频率进行,建议一周两至三次。
During maintenance, the printing needles are removed from the needle sleeve, cleaned with gasoline, dried and re-loaded with appropriate amount of lubricating oil. This work is carried out according to the frequency of equipment used by users. It is recommended that the work be done two to three times a week.
2.打标机头的保养:定期用汽油清洗导轨,擦干后加入适量润滑油即可,该项工作建议两周一次。同时注意在清洗加油的过程中应尽是避免将油加到同步带上。
2. Maintenance of marking machine head: Clean guide rail with gasoline regularly, add proper amount of lubricant after drying, the work is recommended once every two weeks. At the same time, attention should be paid to avoid adding oil to the synchronous belt in the process of cleaning and refueling.
3. 控制器的保养:型槽模具 井盖钢模具 保定雅思 一次性止血带 保定养老院  保定水处理设备 一次性止血带 将控制器电源关闭后,将箱体外盖打开,用干净的友谊比赛空气将内部的灰尘吹干净即可。平时也应多注意机箱外部的防尘工作。
3. Maintenance of the controller: After the power of the controller is turned off, the outer cover of the box is opened and the dust inside is blown clean with clean friendly competition air. At ordinary times, more attention should also be paid to the dust-proof work outside the chassis.
4.计算机的保养:计算机运行时间长了以后,在系统内部也会产生大量的垃圾文件,如不作清理将直接影响软件的正常运行。
4. Maintenance of the computer: After the computer runs for a long time, there will also be a large number of garbage files in the system. If not cleaned up, it will directly affect the normal operation of the software
  • 网站导航 网站首页 关于我们 新闻动态 产品中心 案例展示 联系我们
  • 产品分类 打标机 喷码机
  • 产品推荐

    保定空调维修 精密铸造 矿用电缆挂钩 淤泥固化设备 化粪池钢模具 天津水处理设备

  • 联系我们

    电话:13313028229
    网址:www.dabiaoji58.com.cn
    地址:

联系电话
13313028229

版权 © 保定市科技有限公司 网址:www.dabiaoji58.com.cn 推荐:飞行激光打标机,流水线激光打标机,光纤激光喷码机

网站建设及优化:遨游网络

  • 一键拨号
  • 产品中心
  • 联系我们